Nixpkgs on aarch64-linux is currently stuck on GCC 9
(https://github.com/NixOS/nixpkgs/issues/208412) and using gcc11Stdenv
doesn't work either.
So use c++2a instead of c++20 for now. Unfortunately this means we
can't use some C++20 features for now (like std::span).
These only functioned if a very narrow combination of conditions held:
- The result path does not yet exist (--check did not result in
repeated builds), AND
- The result path is not available from any configured substituters, AND
- No remote builders that can build the path are available.
If any of these do not hold, a derivation would be built 0 or 1 times
regardless of the repeat option. Thus, remove it to avoid confusion.
Disables the SA_RESTART behavior on macOS which causes:
> Restarting of pending calls is requested by setting the SA_RESTART bit
> in sa_flags. The affected system calls include read(2), write(2),
> sendto(2), recvfrom(2), sendmsg(2) and recvmsg(2) on a communications
> channel or a slow device (such as a terminal, but not a regular file)
> and during a wait(2) or ioctl(2).
From: https://man.openbsd.org/sigaction#SA_RESTART
This being set on macOS caused a bug where read() calls to the daemon
socket were blocking after a SIGINT was received. As a result,
checkInterrupt was never reached even though the signal was received
by the signal handler thread.
On Linux, SA_RESTART is disabled by default. This probably effects
other BSDs but I don’t have the ability to test it there right now.
This was caused by -L calling setLogFormat() again, which caused the
creation of a new progress bar without destroying the old one. So we
had two progress bars clobbering each other.
We should change 'logger' to be a smart pointer, but I'll do that in a
future PR.
Fixes#6931.
Some activities are numerous but usually very short (e.g. copying a
source file to the store) which would cause a lot of flickering. So
only show activities that have been running for at least 10 ms.
Starts progress on #5729.
The idea is that we should not have these default methods throwing
"unimplemented". This is a small step in that direction.
I kept `addTempRoot` because it is a no-op, rather than failure. Also,
as a practical matter, it is called all over the place, while doing
other tasks, so the downcasting would be annoying.
Maybe in the future I could move the "real" `addTempRoot` to `GcStore`,
and the existing usecases use a `tryAddTempRoot` wrapper to downcast or
do nothing, but I wasn't sure whether that was a good idea so with a
bias to less churn I didn't do it yet.
Before this change, stdout was closed after the pager exits. This is
fine for non-interactive commands where we want to exit right after
the pager exits anyways, but for interactive things (e.g. nix repl)
this breaks the output after we quit the pager.
Keep the initial stdout fd as part of RunPager, and restore it in
RunPager::~RunPager using dup2.
Doing it as a side-effect of calling LocalStore::makeStoreWritable()
is very ugly.
Also, make sure that stopping the progress bar joins the update
thread, otherwise that thread should be unshared as well.
We can actually just load nss ourselves and call in nss to configure it
and we don't need to run a dummy query entirely to have nss load nss_dns
as a side-effect.
Signed-off-by: Arthur Gautier <baloo@superbaloo.net>
Use `$(libdir)` while installing .pc files looks like a more generic
solution. For example, it will work for distributions like RHEL or
Fedora where .pc files are installed in `/usr/lib64/pkgconfig`.
This avoids an ambiguity where the `StorePathWithOutputs { drvPath, {}
}` could mean "build `brvPath`" or "substitute `drvPath`" depending on
context.
It also brings the internals closer in line to the new CLI, by
generalizing the `Buildable` type is used there and makes that
distinction already.
In doing so, relegate `StorePathWithOutputs` to being a type just for
backwards compatibility (CLI and RPC).
