Today's fixed output derivations and regular derivations differ in a few
ways which are largely orthogonal. This replaces `isFixedOutput` with a
`type` that returns an enum of possible combinations.
Having a colon in the path may cause issues, and having the hash
function indicated isn't actually necessary. We now verify the path
format in the tests to prevent regressions.
Before, we would get:
[deploy@bastion:~]$ nix-store -r /nix/store/grfnl76cahwls0igd2by2pqv0dimi8h2-nixos-system-eris-19.09.20191213.03f3def.drv
these derivations will be built:
/nix/store/3ka4ihvwh6wsyhpd2qa9f59506mnxvx1-initrd-linux-4.19.88.drv
/nix/store/ssxwmll7v21did1c8j027q0m8w6pg41i-unit-prometheus-alertmanager-irc-notifier.service.drv
/nix/store/mvyvkj46ay7pp7b1znqbkck2mq98k0qd-unit-script-network-local-commands-start.drv
/nix/store/vsl1y9mz38qfk6pyirjwnfzfggz5akg6-unit-network-local-commands.service.drv
/nix/store/wi5ighfwwb83fdmav6z6n2fw6npm9ffl-unit-prometheus-hydra-exporter.service.drv
/nix/store/x0qkv535n75pbl3xn6nn1w7qkrg9wwyg-unit-prometheus-packet-sd.service.drv
/nix/store/lv491znsjxdf51xnfxh9ld7r1zg14d52-unit-script-packet-sd-env-key-pre-start.drv
/nix/store/nw4nzlca49agsajvpibx7zg5b873gk9f-unit-script-packet-sd-env-key-start.drv
/nix/store/x674wwabdwjrkhnykair4c8mpxa9532w-unit-packet-sd-env-key.service.drv
/nix/store/ywivz64ilb1ywlv652pkixw3vxzfvgv8-unit-wireguard-wg0.service.drv
/nix/store/v3b648293g3zl8pnn0m1345nvmyd8dwb-unit-script-acme-selfsigned-status.nixos.org-start.drv
/nix/store/zci5d3zvr6fgdicz6k7jjka6lmx0v3g4-unit-acme-selfsigned-status.nixos.org.service.drv
/nix/store/f6pwvnm63d0kw5df0v7sipd1rkhqxk5g-system-units.drv
/nix/store/iax8071knxk9c7krpm9jqg0lcrawf4lc-etc.drv
/nix/store/grfnl76cahwls0igd2by2pqv0dimi8h2-nixos-system-eris-19.09.20191213.03f3def.drv
error: invalid file name 'closure-init-0' in 'exportReferencesGraph'
This was tough to debug, I didn't figure out which one was broken until I did:
nix-store -r /nix/store/grfnl76cahwls0igd2by2pqv0dimi8h2-nixos-system-eris-19.09.20191213.03f3def.drv 2>&1 | grep nix/store | xargs -n1 nix-store -r
and then looking at the remaining build graph:
$ nix-store -r /nix/store/grfnl76cahwls0igd2by2pqv0dimi8h2-nixos-system-eris-19.09.20191213.03f3def.drv
these derivations will be built:
/nix/store/3ka4ihvwh6wsyhpd2qa9f59506mnxvx1-initrd-linux-4.19.88.drv
/nix/store/grfnl76cahwls0igd2by2pqv0dimi8h2-nixos-system-eris-19.09.20191213.03f3def.drv
error: invalid file name 'closure-init-0' in 'exportReferencesGraph'
and knowing the initrd build is before the system, then:
$ nix show-derivation /nix/store/3ka4ihvwh6wsyhpd2qa9f59506mnxvx1-initrd-linux-4.19.88.drv
{
"/nix/store/3ka4ihvwh6wsyhpd2qa9f59506mnxvx1-initrd-linux-4.19.88.drv": {
[...]
"exportReferencesGraph": "closure-init-0 /nix/store/...-stage-1-init.sh closure-mdadm.conf-1 /nix/store/...-mdadm.conf closure-ubuntu.conf-2 ...",
[...]
}
}
I then searched the repo for "in 'exportReferencesGraph'", found this
recently updated regex, and realized it was missing a "-".
Most functions now take a StorePath argument rather than a Path (which
is just an alias for std::string). The StorePath constructor ensures
that the path is syntactically correct (i.e. it looks like
<store-dir>/<base32-hash>-<name>). Similarly, functions like
buildPaths() now take a StorePathWithOutputs, rather than abusing Path
by adding a '!<outputs>' suffix.
Note that the StorePath type is implemented in Rust. This involves
some hackery to allow Rust values to be used directly in C++, via a
helper type whose destructor calls the Rust type's drop()
function. The main issue is the dynamic nature of C++ move semantics:
after we have moved a Rust value, we should not call the drop function
on the original value. So when we move a value, we set the original
value to bitwise zero, and the destructor only calls drop() if the
value is not bitwise zero. This should be sufficient for most types.
Also lots of minor cleanups to the C++ API to make it more modern
(e.g. using std::optional and std::string_view in some places).
Derivations that want to use recursion should now set
requiredSystemFeatures = [ "recursive-nix" ];
to make the daemon socket appear.
Also, Nix should be configured with "experimental-features =
recursive-nix".
This allows Nix builders to call Nix to build derivations, with some
limitations.
Example:
let nixpkgs = fetchTarball channel:nixos-18.03; in
with import <nixpkgs> {};
runCommand "foo"
{
buildInputs = [ nix jq ];
NIX_PATH = "nixpkgs=${nixpkgs}";
}
''
hello=$(nix-build -E '(import <nixpkgs> {}).hello.overrideDerivation (args: { name = "hello-3.5"; })')
$hello/bin/hello
mkdir -p $out/bin
ln -s $hello/bin/hello $out/bin/hello
nix path-info -r --json $hello | jq .
''
This derivation makes a recursive Nix call to build GNU Hello and
symlinks it from its $out, i.e.
# ll ./result/bin/
lrwxrwxrwx 1 root root 63 Jan 1 1970 hello -> /nix/store/s0awxrs71gickhaqdwxl506hzccb30y5-hello-3.5/bin/hello
# nix-store -qR ./result
/nix/store/hwwqshlmazzjzj7yhrkyjydxamvvkfd3-glibc-2.26-131
/nix/store/s0awxrs71gickhaqdwxl506hzccb30y5-hello-3.5
/nix/store/sgmvvyw8vhfqdqb619bxkcpfn9lvd8ss-foo
This is implemented as follows:
* Before running the outer builder, Nix creates a Unix domain socket
'.nix-socket' in the builder's temporary directory and sets
$NIX_REMOTE to point to it. It starts a thread to process
connections to this socket. (Thus you don't need to have nix-daemon
running.)
* The daemon thread uses a wrapper store (RestrictedStore) to keep
track of paths added through recursive Nix calls, to implement some
restrictions (see below), and to do some censorship (e.g. for
purity, queryPathInfo() won't return impure information such as
signatures and timestamps).
* After the build finishes, the output paths are scanned for
references to the paths added through recursive Nix calls (in
addition to the inputs closure). Thus, in the example above, $out
has a reference to $hello.
The main restriction on recursive Nix calls is that they cannot do
arbitrary substitutions. For example, doing
nix-store -r /nix/store/kmwd1hq55akdb9sc7l3finr175dajlby-hello-2.10
is forbidden unless /nix/store/kmwd... is in the inputs closure or
previously built by a recursive Nix call. This is to prevent
irreproducible derivations that have hidden dependencies on
substituters or the current store contents. Building a derivation is
fine, however, and Nix will use substitutes if available. In other
words, the builder has to present proof that it knows how to build a
desired store path from scratch by constructing a derivation graph for
that path.
Probably we should also disallow instantiating/building fixed-output
derivations (specifically, those that access the network, but
currently we have no way to mark fixed-output derivations that don't
access the network). Otherwise sandboxed derivations can bypass
sandbox restrictions and access the network.
When sandboxing is enabled, we make paths appear in the sandbox of the
builder by entering the mount namespace of the builder and
bind-mounting each path. This is tricky because we do a pivot_root()
in the builder to change the root directory of its mount namespace,
and thus the host /nix/store is not visible in the mount namespace of
the builder. To get around this, just before doing pivot_root(), we
branch a second mount namespace that shares its /nix/store mountpoint
with the parent.
Recursive Nix currently doesn't work on macOS in sandboxed mode
(because we can't change the sandbox policy of a running build) and in
non-root mode (because setns() barfs).
Add missing docstring on InstallableCommand. Also, some of these were wrapped
when they're right next to a line longer than the unwrapped line, so we can just
unwrap them to save vertical space.
This adds a command 'nix make-content-addressable' that rewrites the
specified store paths into content-addressable paths. The advantage of
such paths is that 1) they can be imported without signatures; 2) they
can enable deduplication in cases where derivation changes do not
cause output changes (apart from store path hashes).
For example,
$ nix make-content-addressable -r nixpkgs.cowsay
rewrote '/nix/store/g1g31ah55xdia1jdqabv1imf6mcw0nb1-glibc-2.25-49' to '/nix/store/48jfj7bg78a8n4f2nhg269rgw1936vj4-glibc-2.25-49'
...
rewrote '/nix/store/qbi6rzpk0bxjw8lw6azn2mc7ynnn455q-cowsay-3.03+dfsg1-16' to '/nix/store/iq6g2x4q62xp7y7493bibx0qn5w7xz67-cowsay-3.03+dfsg1-16'
We can then copy the resulting closure to another store without
signatures:
$ nix copy --trusted-public-keys '' ---to ~/my-nix /nix/store/iq6g2x4q62xp7y7493bibx0qn5w7xz67-cowsay-3.03+dfsg1-16
In order to support self-references in content-addressable paths,
these paths are hashed "modulo" self-references, meaning that
self-references are zeroed out during hashing. Somewhat annoyingly,
this means that the NAR hash stored in the Nix database is no longer
necessarily equal to the output of "nix hash-path"; for
content-addressable paths, you need to pass the --modulo flag:
$ nix path-info --json /nix/store/iq6g2x4q62xp7y7493bibx0qn5w7xz67-cowsay-3.03+dfsg1-16 | jq -r .[].narHash
sha256:0ri611gdilz2c9rsibqhsipbfs9vwcqvs811a52i2bnkhv7w9mgw
$ nix hash-path --type sha256 --base32 /nix/store/iq6g2x4q62xp7y7493bibx0qn5w7xz67-cowsay-3.03+dfsg1-16
1ggznh07khq0hz6id09pqws3a8q9pn03ya3c03nwck1kwq8rclzs
$ nix hash-path --type sha256 --base32 /nix/store/iq6g2x4q62xp7y7493bibx0qn5w7xz67-cowsay-3.03+dfsg1-16 --modulo iq6g2x4q62xp7y7493bibx0qn5w7xz67
0ri611gdilz2c9rsibqhsipbfs9vwcqvs811a52i2bnkhv7w9mgw
The tmpDirInSandbox is different when in sandboxed vs. non-sandboxed.
Since we don’t know ahead of time here whether sandboxing is enabled,
we need to reset all of the env vars we’ve set previously. This fixes
the issue encountered in https://github.com/NixOS/nixpkgs/issues/70856.
POSIX file locks are essentially incompatible with multithreading. BSD
locks have much saner semantics. We need this now that there can be
multiple concurrent LocalStore::buildPaths() invocations.
Passing `--post-build-hook /foo/bar` to a nix-* command will cause
`/foo/bar` to be executed after each build with the following
environment variables set:
DRV_PATH=/nix/store/drv-that-has-been-built.drv
OUT_PATHS=/nix/store/...build /nix/store/...build-bin /nix/store/...build-dev
This can be useful in particular to upload all the builded artifacts to
the cache (including the ones that don't appear in the runtime closure
of the final derivation or are built because of IFD).
This new feature prints the stderr/stdout output to the `nix-build`
and `nix build` client, and the output is printed in a Nix 2
compatible format:
[nix]$ ./inst/bin/nix-build ./test.nix
these derivations will be built:
/nix/store/ishzj9ni17xq4hgrjvlyjkfvm00b0ch9-my-example-derivation.drv
building '/nix/store/ishzj9ni17xq4hgrjvlyjkfvm00b0ch9-my-example-derivation.drv'...
hello!
bye!
running post-build-hook '/home/grahamc/projects/github.com/NixOS/nix/post-hook.sh'...
post-build-hook: + sleep 1
post-build-hook: + echo 'Signing paths' /nix/store/qr213vjmibrqwnyp5fw678y7whbkqyny-my-example-derivation
post-build-hook: Signing paths /nix/store/qr213vjmibrqwnyp5fw678y7whbkqyny-my-example-derivation
post-build-hook: + sleep 1
post-build-hook: + echo 'Uploading paths' /nix/store/qr213vjmibrqwnyp5fw678y7whbkqyny-my-example-derivation
post-build-hook: Uploading paths /nix/store/qr213vjmibrqwnyp5fw678y7whbkqyny-my-example-derivation
post-build-hook: + sleep 1
post-build-hook: + printf 'very important stuff'
/nix/store/qr213vjmibrqwnyp5fw678y7whbkqyny-my-example-derivation
[nix-shell:~/projects/github.com/NixOS/nix]$ ./inst/bin/nix build -L -f ./test.nix
my-example-derivation> hello!
my-example-derivation> bye!
my-example-derivation (post)> + sleep 1
my-example-derivation (post)> + echo 'Signing paths' /nix/store/c263gzj2kb2609mz8wrbmh53l14wzmfs-my-example-derivation
my-example-derivation (post)> Signing paths /nix/store/c263gzj2kb2609mz8wrbmh53l14wzmfs-my-example-derivation
my-example-derivation (post)> + sleep 1
my-example-derivation (post)> + echo 'Uploading paths' /nix/store/c263gzj2kb2609mz8wrbmh53l14wzmfs-my-example-derivation
my-example-derivation (post)> Uploading paths /nix/store/c263gzj2kb2609mz8wrbmh53l14wzmfs-my-example-derivation
my-example-derivation (post)> + sleep 1
my-example-derivation (post)> + printf 'very important stuff'
[1 built, 0.0 MiB DL]
Co-authored-by: Graham Christensen <graham@grahamc.com>
Co-authored-by: Eelco Dolstra <edolstra@gmail.com>
startProcess does not appear to send the exit code to the helper
correctly. Not sure why this is, but it is probably safe to just
fallback on all sandbox errors.
When sandbox-fallback = true (the default), the Nix builder will fall
back to disabled sandbox mode when the kernel doesn’t allow users to
set it up. This prevents hard errors from occuring in tricky places,
especially the initial installer. To restore the previous behavior,
users can set:
sandbox-fallback = false
in their /etc/nix/nix.conf configuration.
Some kernels disable "unpriveleged user namespaces". This is
unfortunate, but we can still use mount namespaces. Anyway, since each
builder has its own nixbld user, we already have most of the benefits
of user namespaces.
If multiple builds with fail with different errors it will be reflected
in the status code.
eg.
103 => timeout + hash mismatch
105 => timeout + check mismatch
106 => hash mismatch + check mismatch
107 => timeout + hash mismatch + check mismatch
The default nsswitch.conf(5) file in most distros can handle many
different things including host name, user names, groups, etc. In Nix,
we want to limit the amount of impurities that come from these things.
As a result, we should only allow nss to be used for gethostbyname(3)
and getservent(3).
/cc @Ericson2314
This allows many programs (e.g. gcc, clang, cmake) to print colorized
log output (assuming $TERM is set to a value like "xterm").
There are other ways to get colors, in particular setting
CLICOLOR_FORCE, but they're less widely supported and can break
programs that parse tool output.
The value of useChroot is not set yet in the constructor, resulting in
hash rewriting being enabled in certain cases where it should not be.
Fixes#2801
To determine which seccomp filters to install, we were incorrectly
using settings.thisSystem, which doesn't denote the actual system when
--system is used.
Fixes#2791.
This reverts commit a0ef21262f. This
doesn't work in 'nix run' and nix-shell because setns() fails in
multithreaded programs, and Boehm GC mark threads are uncancellable.
Fixes#2646.
Use the same output ordering and format everywhere.
This is such a common issue that we trade the single-line error message for
more readability.
Old message:
```
fixed-output derivation produced path '/nix/store/d4nw9x2sy9q3r32f3g5l5h1k833c01vq-example.com' with sha256 hash '08y4734bm2zahw75b16bcmcg587vvyvh0n11gwiyir70divwp1rm' instead of the expected hash '1xzwnipjd54wl8g93vpw6hxnpmdabq0wqywriiwmh7x8k0lvpq5m'
```
New message:
```
hash mismatch in fixed-output derivation '/nix/store/d4nw9x2sy9q3r32f3g5l5h1k833c01vq-example.com':
wanted: sha256:1xzwnipjd54wl8g93vpw6hxnpmdabq0wqywriiwmh7x8k0lvpq5m
got: sha256:08y4734bm2zahw75b16bcmcg587vvyvh0n11gwiyir70divwp1rm
```
In structured-attributes derivations, you can now specify per-output
checks such as:
outputChecks."out" = {
# The closure of 'out' must not be larger than 256 MiB.
maxClosureSize = 256 * 1024 * 1024;
# It must not refer to C compiler or to the 'dev' output.
disallowedRequisites = [ stdenv.cc "dev" ];
};
outputChecks."dev" = {
# The 'dev' output must not be larger than 128 KiB.
maxSize = 128 * 1024;
};
Also fixed a bug in allowedRequisites that caused it to ignore
self-references.
This is primarily because Derivation::{can,will}BuildLocally() depends
on attributes like preferLocalBuild and requiredSystemFeatures, but it
can't handle them properly because it doesn't have access to the
structured attributes.
E.g. __noChroot and allowedReferences now work correctly. We also now
check that the attribute type is correct. For instance, instead of
allowedReferences = "out";
you have to write
allowedReferences = [ "out" ];
Fixes#2453.
Allow global config settings to be defined in multiple Config
classes. For example, this means that libutil can have settings and
evaluator settings can be moved out of libstore. The Config classes
are registered in a new GlobalConfig class to which config files
etc. are applied.
Relevant to https://github.com/NixOS/nix/issues/2009 in that it
removes the need for ad hoc handling of useCaseHack, which was the
underlying cause of that issue.
Don't bind-mount these to themselves,
mount them into the chroot directory.
Fixes pty issues when using sandbox on CentOS 7.4.
(build of perlPackages.IOTty fails before this change)
E.g.
cannot build on 'ssh://mac1': cannot connect to 'mac1': bash: nix-store: command not found
cannot build on 'ssh://mac2': cannot connect to 'mac2': Host key verification failed.
cannot build on 'ssh://mac3': cannot connect to 'mac3': Received disconnect from 213... port 6001:2: Too many authentication failures
Authentication failed.
This allows building armv[67]l-linux derivations on compatible aarch64
machines. Failure to add the architecture may result from missing
hardware support, in which case we can't run 32-bit binaries and don't
need to restrict them with seccomp anyway,
This was caused by derivations with 'allowSubstitutes = false'. Such
derivations will be built locally. However, if there is another
SubstitionGoal that has the output of the first derivation in its
closure, then the path will be simultaneously built and substituted.
There was a check to catch this situation (via pathIsLockedByMe()),
but it no longer worked reliably because substitutions are now done in
another thread. (Thus the comment 'It can't happen between here and
the lockPaths() call below because we're not allowing multi-threading'
was no longer valid.)
The fix is to handle the path already being locked in both
SubstitutionGoal and DerivationGoal.
All ANSI sequences except color setting are now filtered out. In
particular, terminal resets (such as from NixOS VM tests) are filtered
out.
Also, fix the completely broken tab character handling.
This is needed by nixos-install, which uses the Nix store on the
installation CD as a substituter. We don't want to disable signature
checking entirely because substitutes from cache.nixos.org should
still be checked. So now we can pas "local?trusted=1" to mark only the
Nix store in /nix as not requiring signatures.
Fixes#1819.
Instead, if a fixed-output derivation produces has an incorrect output
hash, we now unconditionally move the outputs to the path
corresponding with the actual hash and register it as valid. Thus,
after correcting the hash in the Nix expression (e.g. in a fetchurl
call), the fixed-output derivation doesn't have to be built again.
It would still be good to have a command for reporting the actual hash
of a fixed-output derivation (instead of throwing an error), but
"nix-build --hash" didn't do that.
This will allow bind and connect to 127.0.0.1, which can reduce purity/
security (if you're running a vulnerable service on localhost) but is
also needed for a ton of test suites, so I'm leaving it turned off by
default but allowing certain derivations to turn it on as needed.
It also allows DNS resolution of arbitrary hostnames but I haven't found
a way to avoid that. In principle I'd just want to allow resolving
localhost but that doesn't seem to be possible.
I don't think this belongs under `build-use-sandbox = relaxed` because we
want it on Hydra and I don't think it's the end of the world.
This makes it slightly more manageable to see at a glance what in a
build's sandbox profile is unique to the build and what is standard. Also
a first step to factoring more of our Darwin logic into scheme functions
that will allow us a bit more flexibility. And of course less of that
nasty codegen in C++! 😀
I needed this to test ACL/xattr removal in
canonicalisePathMetaData(). Might also be useful if you need to build
old Nixpkgs that doesn't have the required patches to remove
setuid/setgid creation.
Since we may use a dedicated file descriptor in the future, this
allows us to change it. So builders can do
if [[ -n $NIX_LOG_FD ]]; then
echo "@nix { message... }" >&$NIX_LOG_FD
fi
Nix can now automatically run the garbage collector during builds or
while adding paths to the store. The option "min-free = <bytes>"
specifies that Nix should run the garbage collector whenever free
space in the Nix store drops below <bytes>. It will then delete
garbage until "max-free" bytes are available.
Garbage collection during builds is asynchronous; running builds are
not paused and new builds are not blocked. However, there also is a
synchronous GC run prior to the first build/substitution.
Currently, no old GC roots are deleted (as in "nix-collect-garbage
-d").
Without this, substitute info is fetched sequentially, which is
superslow. In the old UI (e.g. nix-build), we call printMissing(),
which calls queryMissing(), thereby preheating the binary cache
cache. But the new UI doesn't do that.
In particular, drop the "build-" and "gc-" prefixes which are
pointless. So now you can say
nix build --no-sandbox
instead of
nix build --no-build-use-sandbox
This allows builds to call setuid binaries. This was previously
possible until we started using seccomp. Turns out that seccomp by
default disallows processes from acquiring new privileges. Generally,
any use of setuid binaries (except those created by the builder
itself) is by definition impure, but some people were relying on this
ability for certain tests.
Example:
$ nix build '(with import <nixpkgs> {}; runCommand "foo" {} "/run/wrappers/bin/ping -c 1 8.8.8.8; exit 1")' --no-allow-new-privileges
builder for ‘/nix/store/j0nd8kv85hd6r4kxgnwzvr0k65ykf6fv-foo.drv’ failed with exit code 1; last 2 log lines:
cannot raise the capability into the Ambient set
: Operation not permitted
$ nix build '(with import <nixpkgs> {}; runCommand "foo" {} "/run/wrappers/bin/ping -c 1 8.8.8.8; exit 1")' --allow-new-privileges
builder for ‘/nix/store/j0nd8kv85hd6r4kxgnwzvr0k65ykf6fv-foo.drv’ failed with exit code 1; last 6 log lines:
PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
64 bytes from 8.8.8.8: icmp_seq=1 ttl=46 time=15.2 ms
Fixes#1429.
Functions like copyClosure() had 3 bool arguments, which creates a
severe risk of mixing up arguments.
Also, implement copyClosure() using copyPaths().
Sandboxes cannot be nested, so if Nix's build runs inside a sandbox,
it cannot use a sandbox itself. I don't see a clean way to detect
whether we're in a sandbox, so use a test-specific hack.
https://github.com/NixOS/nix/issues/1413
Even with "build-use-sandbox = false", we now use sandboxing with a
permissive profile that allows everything except the creation of
setuid/setgid binaries.
Also, add rules to allow fixed-output derivations to access the
network.
These rules are sufficient to build stdenvDarwin without any
__sandboxProfile magic.
The filename used was not unique and owned by the build user, so
builds could fail with
error: while setting up the build environment: cannot unlink ‘/nix/store/99i210ihnsjacajaw8r33fmgjvzpg6nr-bison-3.0.4.drv.sb’: Permission denied
Fixes
src/libstore/build.cc:2321:45: error: non-constant-expression cannot be narrowed from type 'int' to 'scmp_datum_t' (aka 'unsigned long') in initializer list [-Wc++11-narrowing]
This prevents builders from setting the S_ISUID or S_ISGID bits,
preventing users from using a nixbld* user to create a setuid/setgid
binary to interfere with subsequent builds under the same nixbld* uid.
This is based on aszlig's seccomp code
(47f587700d).
Reported by Linus Heckemann.
This is useful when we're using a diverted store (e.g. "--store
local?root=/tmp/nix") in conjunction with a statically-linked sh from
the host store (e.g. "sandbox-paths =/bin/sh=/nix/store/.../bin/busybox").
There is a security issue when a build accidentally stores its $TMPDIR
in some critical place, such as an RPATH. If
TMPDIR=/tmp/nix-build-..., then any user on the system can recreate
that directory and inject libraries into the RPATH of programs
executed by other users. Since /build probably doesn't exist (or isn't
world-writable), this mitigates the issue.
This is useful for one-off situations where you want to specify a
builder on the command line instead of having to mess with
nix.machines. E.g.
$ nix-build -A hello --argstr system x86_64-darwin \
--option builders 'root@macstadium1 x86_64-darwin'
will perform the specified build on "macstadium1".
It also removes the need for a separate nix.machines file since you
can specify builders in nix.conf directly. (In fact nix.machines is
yet another hack that predates the general nix.conf configuration
file, IIRC.)
Note: this option is supported by the daemon for trusted users. The
fact that this allows trusted users to specify paths to SSH keys to
which they don't normally have access is maybe a bit too much trust...
For backwards compatibility, if the URI is just a hostname, ssh://
(i.e. LegacySSHStore) is prepended automatically.
Also, all fields except the URI are now optional. For example, this is
a valid nix.machines file:
local?root=/tmp/nix
This is useful for testing the remote build machinery since you don't
have to mess around with ssh.
This is to simplify remote build configuration. These environment
variables predate nix.conf.
The build hook now has a sensible default (namely build-remote).
The current load is kept in the Nix state directory now.
Since build-remote uses buildDerivation() now, we don't need to copy
the .drv file anymore. This greatly reduces the set of input paths
copied to the remote side (e.g. from 392 to 51 store paths for GNU
hello on x86_64-darwin).
The typical use is to inherit Config and add Setting<T> members:
class MyClass : private Config
{
Setting<int> foo{this, 123, "foo", "the number of foos to use"};
Setting<std::string> bar{this, "blabla", "bar", "the name of the bar"};
MyClass() : Config(readConfigFile("/etc/my-app.conf"))
{
std::cout << foo << "\n"; // will print 123 unless overriden
}
};
Currently, this is used by Store and its subclasses for store
parameters. You now get a warning if you specify a non-existant store
parameter in a store URI.
This fixes "No such file or directory" when opening /dev/ptmx
(e.g. http://hydra.nixos.org/build/51094249).
The reason appears to be some changes to /dev/ptmx / /dev/pts handling
between Linux 4.4 and 4.9. See
https://patchwork.kernel.org/patch/7832531/.
The fix is to go back to mounting a proper /dev/pts instance inside
the sandbox. Happily, this now works inside user namespaces, even for
unprivileged users. So
NIX_REMOTE=local?root=/tmp/nix nix-build \
'<nixpkgs/nixos/tests/misc.nix>' -A test
works for non-root users.
The downside is that the fix breaks sandbox builds on older kernels
(probably pre-4.6), since mounting a devpts fails inside user
namespaces for some reason I've never been able to figure out. Builds
on those systems will fail with
error: while setting up the build environment: mounting /dev/pts: Invalid argument
Ah well.
This allows various Store implementations to provide different ways to
get build logs. For example, BinaryCacheStore can get the build logs
from the binary cache.
Also, remove the log-servers option since we can use substituters for
this.
Previously, the Settings class allowed other code to query for string
properties, which led to a proliferation of code all over the place making
up new options without any sort of central registry of valid options. This
commit pulls all those options back into the central Settings class and
removes the public get() methods, to discourage future abuses like that.
Furthermore, because we know the full set of options ahead of time, we
now fail loudly if someone enters an unrecognized option, thus preventing
subtle typos. With some template fun, we could probably also dump the full
set of options (with documentation, defaults, etc.) to the command line,
but I'm not doing that yet here.
This allows <nix/fetchurl.nix> to fetch private Git/Mercurial
repositories, e.g.
import <nix/fetchurl.nix> {
url = https://edolstra@bitbucket.org/edolstra/my-private-repo/get/80a14018daed.tar.bz2;
sha256 = "1mgqzn7biqkq3hf2697b0jc4wabkqhmzq2srdymjfa6sb9zb6qs7";
}
where /etc/nix/netrc contains:
machine bitbucket.org
login edolstra
password blabla...
This works even when sandboxing is enabled.
To do: add unpacking support (i.e. fetchzip functionality).
Because config.h can #define things like _FILE_OFFSET_BITS=64 and not
every compilation unit includes config.h, we currently compile half of
Nix with _FILE_OFFSET_BITS=64 and other half with _FILE_OFFSET_BITS
unset. This causes major havoc with the Settings class on e.g. 32-bit ARM,
where different compilation units disagree with the struct layout.
E.g.:
diff --git a/src/libstore/globals.cc b/src/libstore/globals.cc
@@ -166,6 +166,8 @@ void Settings::update()
_get(useSubstitutes, "build-use-substitutes");
+ fprintf(stderr, "at Settings::update(): &useSubstitutes = %p\n", &nix::settings.useSubstitutes);
_get(buildUsersGroup, "build-users-group");
diff --git a/src/libstore/remote-store.cc b/src/libstore/remote-store.cc
+++ b/src/libstore/remote-store.cc
@@ -138,6 +138,8 @@ void RemoteStore::initConnection(Connection & conn)
void RemoteStore::setOptions(Connection & conn)
{
+ fprintf(stderr, "at RemoteStore::setOptions(): &useSubstitutes = %p\n", &nix::settings.useSubstitutes);
conn.to << wopSetOptions
Gave me:
at Settings::update(): &useSubstitutes = 0xb6e5c5cb
at RemoteStore::setOptions(): &useSubstitutes = 0xb6e5c5c7
That was not a fun one to debug!
This writes info about every path in the closure in the same format as
‘nix path-info --json’. Thus it also includes NAR hashes and sizes.
Example:
[
{
"path": "/nix/store/10h6li26i7g6z3mdpvra09yyf10mmzdr-hello-2.10",
"narHash": "sha256:0ckdc4z20kkmpqdilx0wl6cricxv90lh85xpv2qljppcmz6vzcxl",
"narSize": 197648,
"references": [
"/nix/store/10h6li26i7g6z3mdpvra09yyf10mmzdr-hello-2.10",
"/nix/store/27binbdy296qvjycdgr1535v8872vz3z-glibc-2.24"
],
"closureSize": 20939776
},
{
"path": "/nix/store/27binbdy296qvjycdgr1535v8872vz3z-glibc-2.24",
"narHash": "sha256:1nfn3m3p98y1c0kd0brp80dn9n5mycwgrk183j17rajya0h7gax3",
"narSize": 20742128,
"references": [
"/nix/store/27binbdy296qvjycdgr1535v8872vz3z-glibc-2.24"
],
"closureSize": 20742128
}
]
Fixes#1134.
Previously, all derivation attributes had to be coerced into strings
so that they could be passed via the environment. This is lossy
(e.g. lists get flattened, necessitating configureFlags
vs. configureFlagsArray, of which the latter cannot be specified as an
attribute), doesn't support attribute sets at all, and has size
limitations (necessitating hacks like passAsFile).
This patch adds a new mode for passing attributes to builders, namely
encoded as a JSON file ".attrs.json" in the current directory of the
builder. This mode is activated via the special attribute
__structuredAttrs = true;
(The idea is that one day we can set this in stdenv.mkDerivation.)
For example,
stdenv.mkDerivation {
__structuredAttrs = true;
name = "foo";
buildInputs = [ pkgs.hello pkgs.cowsay ];
doCheck = true;
hardening.format = false;
}
results in a ".attrs.json" file containing (sans the indentation):
{
"buildInputs": [],
"builder": "/nix/store/ygl61ycpr2vjqrx775l1r2mw1g2rb754-bash-4.3-p48/bin/bash",
"configureFlags": [
"--with-foo",
"--with-bar=1 2"
],
"doCheck": true,
"hardening": {
"format": false
},
"name": "foo",
"nativeBuildInputs": [
"/nix/store/10h6li26i7g6z3mdpvra09yyf10mmzdr-hello-2.10",
"/nix/store/4jnvjin0r6wp6cv1hdm5jbkx3vinlcvk-cowsay-3.03"
],
"propagatedBuildInputs": [],
"propagatedNativeBuildInputs": [],
"stdenv": "/nix/store/f3hw3p8armnzy6xhd4h8s7anfjrs15n2-stdenv",
"system": "x86_64-linux"
}
"passAsFile" is ignored in this mode because it's not needed - large
strings are included directly in the JSON representation.
It is up to the builder to do something with the JSON
representation. For example, in bash-based builders, lists/attrsets of
string values could be mapped to bash (associative) arrays.
This closes a long-time bug that allowed builds to hang Nix
indefinitely (regardless of timeouts) simply by doing
exec > /dev/null 2>&1; while true; do true; done
Now, on EOF, we just send SIGKILL to the child to make sure it's
really gone.
That is, when build-repeat > 0, and the output of two rounds differ,
then print a warning rather than fail the build. This is primarily to
let Hydra check reproducibility of all packages.
These syscalls are only available in 32bit architectures, but libseccomp
should handle them correctly even if we're on native architectures that
do not have these syscalls.
Signed-off-by: aszlig <aszlig@redmoonstudios.org>
Commands such as "cp -p" also use fsetxattr() in addition to fchown(),
so we need to make sure these syscalls always return successful as well
in order to avoid nasty "Invalid value" errors.
Signed-off-by: aszlig <aszlig@redmoonstudios.org>
What we basically want is a seccomp mode 2 BPF program like this but for
every architecture:
BPF_STMT(BPF_LD+BPF_W+BPF_ABS, offsetof(struct seccomp_data, nr)),
BPF_JUMP(BPF_JMP+BPF_JEQ+BPF_K, __NR_chown, 4, 0),
BPF_JUMP(BPF_JMP+BPF_JEQ+BPF_K, __NR_fchown, 3, 0),
BPF_JUMP(BPF_JMP+BPF_JEQ+BPF_K, __NR_fchownat, 2, 0),
BPF_JUMP(BPF_JMP+BPF_JEQ+BPF_K, __NR_lchown, 1, 0),
BPF_STMT(BPF_RET+BPF_K, SECCOMP_RET_ALLOW),
BPF_STMT(BPF_RET+BPF_K, SECCOMP_RET_ERRNO)
However, on 32 bit architectures we do have chown32, lchown32 and
fchown32, so we'd need to add all the architecture blurb which
libseccomp handles for us.
So we only need to make sure that we add the 32bit seccomp arch while
we're on x86_64 and otherwise we just stay at the native architecture
which was set during seccomp_init(), which more or less replicates
setting 32bit personality during runChild().
The FORCE_SUCCESS() macro here could be a bit less ugly but I think
repeating the seccomp_rule_add() all over the place is way uglier.
Another way would have been to create a vector of syscalls to iterate
over, but that would make error messages uglier because we can either
only print the (libseccomp-internal) syscall number or use
seccomp_syscall_resolve_num_arch() to get the name or even make the
vector a pair number/name, essentially duplicating everything again.
Signed-off-by: aszlig <aszlig@redmoonstudios.org>
This reverts commit ff0c0b645c.
We're going to use seccomp to allow "cp -p" and force chown-related
syscalls to always return 0.
Signed-off-by: aszlig <aszlig@redmoonstudios.org>
For example, you can now set
build-sandbox-paths = /dev/nvidiactl?
to specify that /dev/nvidiactl should only be mounted in the sandbox
if it exists in the host filesystem. This is useful e.g. for EC2
images that should support both CUDA and non-CUDA instances.
We can now write
throw Error("file '%s' not found", path);
instead of
throw Error(format("file '%s' not found") % path);
and similarly
printError("file '%s' not found", path);
instead of
printMsg(lvlError, format("file '%s' not found") % path);
This largely reverts c68e5913c7. Running
builds as root breaks "cp -p", since when running as root, "cp -p"
assumes that it can succesfully chown() files. But that's not actually
the case since the user namespace doesn't provide a complete uid
mapping. So it barfs with a fatal error message ("cp: failed to
preserve ownership for 'foo': Invalid argument").
This fixes an assertion failure in "assert(goal);" in
Worker::waitForInput() after a substitution goal is cancelled by the
termination of another goal. The problem was the line
//worker.childTerminated(shared_from_this()); // FIXME
in the SubstitutionGoal destructor. This was disabled because
shared_from_this() obviously doesn't work from a destructor. So we now
use a real pointer for object identity.
For example, you can now say:
configureFlags = "--prefix=${placeholder "out"} --includedir=${placeholder "dev"}";
The strings returned by the ‘placeholder’ builtin are replaced at
build time by the actual store paths corresponding to the specified
outputs.
Previously, you had to work around the inability to self-reference by doing stuff like:
preConfigure = ''
configureFlags+=" --prefix $out --includedir=$dev"
'';
or rely on ad-hoc variable interpolation semantics in Autoconf or Make
(e.g. --prefix=\$(out)), which doesn't always work.
This makes it easier to create a diverted store, i.e.
NIX_REMOTE="local?root=/tmp/root"
instead of
NIX_REMOTE="local?real=/tmp/root/nix/store&state=/tmp/root/nix/var/nix" NIX_LOG_DIR=/tmp/root/nix/var/log
